SikaTop-122 HS Polymer Modified Repair Mortar (30kg)
SikaTop-122 HS is a pre-batched, one-component polymer modified repair mortar for structural and cosmetic concrete repairs on buildings, bridges and infrastructure — mixed with water only, applicable up to 40mm thick in vertical layers. Supplied by ARM Build Mart, authorised Sika dealer, Tamil Nadu.
Brand
Category
More Info
Product Overview
SikaTop-122 HS (also referred to as Sikatop 122HS) is a pre-batched, one-component, polymer modified repair mortar supplied as a grey powder in 30kg bags — it only needs to be mixed with water on site. ARM Build Mart is an authorised Sika dealer with 5 branches across Tamil Nadu (Pudukkottai, Trichy, Sivagangai, Thanjavur, Karaikudi) and statewide dispatch to all 38 districts.
It is designed for structural and cosmetic repairs to spalling and damaged concrete across buildings, bridges, and general infrastructure/superstructure work, and can be applied by hand-troweling or mechanical wet-spray in layers up to 40mm thick on vertical surfaces.
Features & Benefits
- Easy to use — only needs mixing with water, no separate bonding liquid required
- Suitable for both structural and cosmetic repairs
- Can be applied up to 40mm thick in a single vertical layer
- Strong adhesion to prepared concrete substrates
- Compatible with hand-trowel and mechanical wet-spray application
- Rapid strength development with high ultimate strength (~55 N/mm² at 28 days)
Applications & Usage
Spalled Concrete Repair
Restores damaged, delaminated or spalling concrete sections on beams, columns and slabs.
Bridge & Infrastructure Repair
High-strength patch repairs on bridges and civil infrastructure exposed to traffic and weathering loads.
Vertical & Overhead Patching
Formulated to be applied and stay in place on vertical surfaces up to 40mm thick per layer.
Cosmetic Concrete Repair
Suitable for surface-level cosmetic patching where a lower bond-strength requirement (0.7 MPa) applies.
Not suitable for: application in direct sun or strong wind without protection, or with extra water added beyond the recommended dosage — this causes discoloration and cracking. Not for use below +5°C or above +40°C ambient/substrate temperature.
Dosage, Mixing & Consumption
Water:powder ratio of 0.13 by weight — approximately 3.9 litres of water per 30kg bag. Consumption is approximately 2100 kg of mixed mortar per m³ at this ratio.
- Prepare the substrate: remove delaminated, weak or damaged concrete by mechanical means or high-pressure water-blasting (up to 110 MPa); cut repair edges at 90–135° and roughen the surface for mechanical key.
- Clean exposed reinforcement by abrasive blasting or pressure water-jetting (up to 60 MPa) to remove rust and contamination.
- Pre-dampen the substrate so it is saturated but surface-dry before applying mortar.
- Mix mechanically using a low-speed drill at a maximum of 500 rpm: add 80–90% of the water first, then the powder, then the remaining water, and mix for a minimum of 3 minutes to a uniform consistency. Do not use a tilting concrete mixer.
- Apply the mortar by hand-trowel or mechanical wet-spray, pressing firmly onto the substrate (wet-on-wet where a bonding primer is used), within the pot life of ~30 minutes at +20°C.
- Do not add extra water during surface finishing — this causes discoloration and cracking. Protect the fresh mortar from rapid evaporation, direct sun, strong wind and frost during cure.
Full Specifications
| Product Type | Pre-batched, one-component, polymer modified repair mortar (mix with water only) |
| Appearance | Grey powder |
| Packaging | 30kg bag |
| Shelf Life | 6 months from date of production, in original sealed, undamaged packaging |
| Storage Conditions | +5°C to +40°C, dry conditions, in original sealed packaging |
| Mixing Ratio (Water:Powder) | 0.13 by weight (~3.9 L water per 30kg bag) |
| Bulk Density | ~1.3 kg/L at 27°C |
| Pot Life | ~30 minutes at +20°C |
| Compressive Strength (ASTM C109, +30°C) | 1 day: ~20 N/mm²; 7 days: ~35 N/mm²; 28 days: ~55 N/mm² |
| Flexural Strength (ASTM C293-79, +30°C) | 7 days: ~3 N/mm²; 28 days: ~5 N/mm² |
| Bond/Pull-Off Strength | Structural repairs: 1.2–1.5 MPa minimum; non-structural/cosmetic: 0.7 MPa minimum |
| Maximum Layer Thickness | Up to 40mm in a single vertical layer |
| Application Temperature | +5°C to +40°C (ambient and substrate) |
| Consumption | ~2100 kg mixed mortar per m³ |
| Mixing Equipment | Low-speed electric drill, max 500 rpm, minimum 3 minutes mix time; do not use a tilting concrete mixer |
| Chloride Content | [NOT STATED ON TDS — confirm with Sika technical team before publishing] |
Storage & Handling
- Store in original, sealed, undamaged packaging in dry conditions between +5°C and +40°C
- Use within 6 months of the production date
- Protect bags from moisture prior to use
Why Buy From ARM Build Mart
- Authorised Sika distributor with batch-fresh stock
- Technical support for mixing and application queries
- GST invoicing for project and dealer orders
- Bulk and project pricing available
- 5-branch network across Tamil Nadu with statewide dispatch
Frequently Asked Questions
How much water do I add per 30kg bag of SikaTop-122 HS?
About 3.9 litres, giving a water:powder ratio of 0.13 by weight. Add 80–90% of the water first, then the powder, then the rest.
Can I apply this on a vertical wall or column?
Yes — it’s designed to stay in place on vertical surfaces in layers up to 40mm thick without sagging.
How long do I have to use the mixed mortar?
Around 30 minutes at 20°C. Don’t add extra water once mixing is done — it causes discoloration and cracking.
Do you supply SikaTop-122 HS outside Pudukkottai/Trichy/Sivagangai/Thanjavur/Karaikudi?
Yes — we dispatch this and other Sika products to all 38 districts of Tamil Nadu for bulk and project orders. Share your delivery location and quantity for a quote.

