SikaShield P24 MG IN 4mm SBS/APP Waterproofing Membrane (Roll)
SikaShield P24 MG IN 4mm is an APP-modified bituminous torch-applied waterproofing membrane with a mineral granule finish, for terraces, roofs, podiums and bridge decks. 1.0m x 10.0m roll (10 sqm coverage). Supplied by ARM Build Mart, authorised Sika dealer, Tamil Nadu.
Brand
Category
More Info
Product Overview
SikaShield P24 MG IN 4mm (also known as Sikashield P24 APP) is an APP-modified bituminous waterproofing membrane, 4mm thick, reinforced with non-woven polyester fabric, finished with mineral granules on top and a burn-off polyethylene film underside for torch application. ARM Build Mart is an authorised Sika dealer with 5 branches across Tamil Nadu (Pudukkottai, Trichy, Sivagangai, Thanjavur, Karaikudi) and statewide dispatch to all 38 districts.
It is used for waterproofing balconies, terraces, flat and sloping roofs (up to 15% gradient), bridge decks under an asphalt wearing course, horizontal reinforced concrete slabs, and podium decks — as either an exposed single-layer system or as part of a multi-layer roofing build-up.
Features & Benefits
- Excellent water tightness (≥ 10 kPa, EN 1928 Method B, 24h)
- Flexible down to -2°C — suitable for long-term outdoor exposure
- Decorative mineral granule top surface — immediately usable/paintable after installation
- Low water absorption
- Tiles can be placed directly onto the membrane without an additional protection layer
- High softening point (≥145°C) and no flow at +120°C for 2 hours — stable in hot climates
Applications & Usage
Terraces & Flat Roofs
Exposed single-layer waterproofing for roof slopes up to 15%, with a decorative, durable granule finish.
Bridge Decks
Waterproofing layer under the asphalt wearing course on reinforced concrete bridge decks.
Podiums & Concrete Slabs
Horizontal waterproofing beneath tiling, landscaping or vehicular deck finishes.
Sloping Roofs
Multi-layer or single-layer torch-applied systems on pitched roof structures.
Not suitable for: substrates with moisture content above 6%, new concrete younger than 28 days or with pull-off strength below 1.5 N/mm², or application below +10°C ambient/substrate temperature.
Application Method
- Confirm the concrete substrate has cured for at least 28 days and achieves a pull-off strength of ≥ 1.5 N/mm²; mechanically remove cement laitance.
- Ensure the surface is clean, dry, and free of grease, oil and dust, with substrate moisture below 6%.
- Position and align the membrane roll, allowing 80–100mm side overlaps and 150mm end overlaps; cut corners at 45° (80–100mm per side) and stagger all joints so they don’t coincide.
- Torch-apply by heating the underside burn-off film evenly until the bitumen flows, then roll the membrane into place with firm, continuous pressure — work only within the stated ambient/substrate temperature range of +10°C to +40°C.
- Heat and seal all overlaps fully to ensure continuous adhesion — insufficient heating at laps is a common cause of leaks.
- Use flat-profile footwear during and after installation to avoid puncturing the membrane.
Full Specifications
| Chemical Base | APP (Atactic Polypropylene) modified bitumen |
| Reinforcement | Non-woven polyester fabric |
| Top Surface | Mineral granules, grey |
| Bottom Surface | Polyethylene burn-off film, black |
| Thickness | 4mm (+0.3/-0.2mm, EN 1849-1) |
| Roll Dimensions | 1.0m width x 10.0m length (10 m² per roll) |
| Tensile Strength – Longitudinal | (600±150) N/50mm |
| Tensile Strength – Transverse | (400±150) N/50mm |
| Elongation at Break | (40±10)% both directions |
| Tear Strength – Longitudinal | (300±100) N |
| Tear Strength – Transverse | (200±100) N |
| Cold Flexibility | ≤ -2°C (EN 1109) |
| Softening Point | ≥ 145°C (ASTM D36) |
| Flow Resistance | No flow at +120°C for 2 hours (EN 1110) |
| Watertightness | ≥ 10 kPa, Method B, 24h (EN 1928) |
| Application Temperature | +10°C to +40°C (ambient and substrate) |
| Overlaps | 80–100mm sides, 150mm ends |
| Shelf Life | 12 months from date of production, unopened packaging |
| Storage | +5°C to +35°C, stored vertically (standing), rolls not stacked on pallets |
| Substrate Pull-Off Strength Required | ≥ 1.5 N/mm² (new concrete, cured 28 days) |
| Reinforcement Melting Point | Polyester reinforcement melts at approximately +260°C — caution during torch application |
Storage & Handling
- Store unopened rolls vertically (standing on end), not stacked flat or on pallets
- Keep between +5°C and +35°C, away from direct sunlight and heat sources
- Use within 12 months of the production date
- Handle with flat-profile footwear on-site to prevent membrane puncture
Why Buy From ARM Build Mart
- Authorised Sika distributor with batch-fresh stock
- Technical support for torch-application and overlap detailing queries
- GST invoicing for project and dealer orders
- Bulk and project pricing available
- 5-branch network across Tamil Nadu with statewide dispatch
Frequently Asked Questions
How much area does one roll of SikaShield P24 MG IN 4mm cover?
Each roll is 1.0m x 10.0m, covering 10 sqm before overlaps. Order slightly extra to account for the 80–100mm side and 150mm end overlaps.
Can this membrane be laid on new concrete?
Only after the concrete has cured for at least 28 days and achieves a pull-off strength of 1.5 N/mm² or higher; cement laitance must be mechanically removed first.
Does the membrane need a protective screed on top?
No — the mineral granule top surface is designed to be exposed or tiled over directly, so a separate protection screed isn’t required for most applications.
Do you supply this outside Pudukkottai/Trichy/Sivagangai/Thanjavur/Karaikudi?
Yes — we dispatch this and other Sika products to all 38 districts of Tamil Nadu for bulk and project orders. Share your delivery location and quantity for a quote.

