Brand:

Nitobond EP

₹1,099.00

Epoxy resin concrete bonding agent

More Info

Product Overview

Fosroc Nitobond EP is a solvent-free, two-part epoxy resin bonding agent used to bond fresh wet cementitious materials to existing cementitious surfaces. It is supplied in pre-weighed quantities as a white base and a green hardener — the colour change on mixing gives visual confirmation that the two components have been fully blended.

Its long open life makes it suitable for use with formwork, or where additional steel reinforcement has to be fitted after the bonding coat is applied. Nitobond EP can be applied by brush to both dry and damp substrates, and is equally suited to internal and external applications. It may also be used as part of a repair system where a bonding agent is required, or where the substrate is likely to remain permanently damp or wet.

Nitobond EP is GreenPro Ecolabel certified by CII.

Features & Benefits

  • Solvent-free epoxy resin formulation
  • Two-part system in pre-weighed packs — no site batching
  • White base and green hardener confirm correct mixing visually
  • Bond strength exceeds the tensile strength of good quality concrete
  • Long overlay time allows concrete to be placed without risk of delamination
  • Acts as a barrier coat against the migration of chloride ions
  • Applies to dry or damp substrates
  • Brush applied — no specialist equipment required
  • Suitable for internal and external use
  • Suitable for use with formwork and added steel reinforcement

Applications & Usage

Roads & Bridges

Bonding fresh concrete to existing structural concrete in highway and bridge works.

Pavements & Loading Bays

For horizontal surfaces subject to heavy traffic and repeated loading.

Factories & Industrial Floors

Bonded and granolithic floor toppings over existing concrete slabs.

Building Segment

General construction bonding of new cementitious material to old.

Vertical Surfaces

Where mortar or concrete can be supported by formwork during placement.

Concrete Repair Systems

As a bonding agent and substrate barrier where the substrate stays damp or wet.

Surface Preparation & Application

Surface Preparation

  • All surfaces must be firm, dust free and clean before application.
  • Remove all laitance by etching with Reebaklens and wire-brushing.
  • Where required, chip back the existing concrete to a sound substrate.
  • Remove oil or grease contamination using a strong industrial detergent or organic degreaser.
  • Wash the surface thoroughly with water and dry it before applying Nitobond EP.

Mixing

  • Stir the base and hardener components separately to disperse any settlement.
  • Pour the entire contents of the hardener can into the base container.
  • Mix thoroughly until a uniform colour is obtained.
  • For application below 10°C, warm the separate components in hot water to a maximum of 25°C before mixing.

Coating

  • Apply an unbroken coating by brush across the full prepared area.
  • Where used as a substrate/repair barrier, apply one coat and allow it to gel, then apply a second coat as the bonding coat.
  • For sprayed concrete repairs, dust-free sharp sand may be scattered over this coat and left to harden.
  • Erect and fix any required steel reinforcement and formwork securely in place as soon as the Nitobond EP has been applied.

Cleaning

  • Clean tools, equipment and mixers with Nitoflor Sol immediately after use.
  • Hardened material can only be removed mechanically.

Full Specifications

Brand Fosroc
Product Name Nitobond EP
Product Type Epoxy Resin Concrete Bonding Agent
Composition Solvent-free epoxy resin, two-part (base + hardener)
Component Colours White base, green hardener
Specific Gravity 1.15 – 1.2 g/cc
Pot Life 5 – 6 hrs at 20°C | 2 – 3 hrs at 30°C
Overlay Time 10 hrs at 20°C | 6 hrs at 30°C
Full Cure 7 days at 20°C | 5 days at 30°C
Compressive Strength 50 N/mm² at 7 days (BS 6319 Pt 2)
Flexural Strength 35 N/mm² at 7 days (BS 6319 Pt 3)
Tensile Strength 20 N/mm² at 7 days (BS 6319 Pt 7)
Shear Strength 10 N/mm² at 7 days (BS 6319 Pt 4)
Minimum Application Temperature 10°C
Coverage Approximately 2.6 m² per litre
Available Pack Sizes 0.5 Litre, 1 Litre, 4 Litre
Cleaning Solvent Nitoflor Sol (5 L & 20 L)
Shelf Life 12 months unopened, stored below 35°C
Certification GreenPro Ecolabel, certified by CII
Country of Origin India

Typical physical properties above are derived from testing in a controlled laboratory environment. Results from field-applied samples may vary depending on actual site conditions.

Coverage & Estimating

Nitobond EP covers approximately 2.6 m² per litre. Actual coverage depends on the texture and porosity of the substrate being covered.

0.5 Litre pack Approx. 1.3 m²
1 Litre pack Approx. 2.6 m²
4 Litre pack Approx. 10.4 m²

Storage & Handling

  • Shelf life is 12 months in unopened containers stored under normal warehouse conditions below 35°C.
  • Do not apply when the temperature is below 10°C.
  • Nitobond EP is inflammable. No naked flame should be allowed near the site and there should be no smoking during use.
  • Avoid contact with skin and eyes. Gloves should be worn when handling these products.
  • If contact with the resin occurs, wash immediately with a strong detergent or a resin removing cream.
  • Eye contamination must be washed immediately with plenty of water and medical treatment sought.

Why Buy From ARM Build Mart

  • Genuine Fosroc stock through authorised channels
  • Batch-fresh material with verifiable manufacturing dates
  • All three pack sizes available
  • Nitoflor Sol cleaning solvent stocked alongside
  • GST invoice issued on every order
  • Bulk and project pricing on request
  • Six branches: Pudukkottai, Trichy, Trichy Depot, Kottaipattinam, Aranthangi and Karaikudi
  • Delivery across the Pudukkottai and Trichy region